Skip to content

IR Thermography Procurement for Specifiers

A specification for IR thermography, a UAV thermal payload or a domed PTZ aperture is decided by five numbers and one compliance answer: spectral band, detector array, IFOV, NETD, radiometric output, and whether the manufacturer is a covered entity under NDAA Section 889. This page sets out what to write for each, how the aperture optic in front of the detector changes the result, and the compliance position of this catalog as counted per listing — so a requirement can be built that a real camera can actually meet.

Specifier support Mon–Fri 9–5 PT. Volume terms and NET pricing are on the procurement page.

What to specify, and why it decides the award

Each row is written to be lifted into a statement of work. The third column is the part most specifications leave out, and it is the part that separates two cameras sold on the same pixel count.

IR thermography specification parameters, what to write and why each decides the award
ParameterWrite in the specificationWhy it decides the award
Spectral band8–14 µm (LWIR) for building, electrical and mechanical targets near ambient temperature. 3–5 µm (MWIR) only for hot targets — kilns, flare stacks, engine exhaust.LWIR is where a roof, a switchgear lug or a person radiates most of their energy at 20–100 °C. An MWIR camera specified for the same survey sees less contrast for more money.
Detector arrayThe native pixel array, not the marketing class: 320×240, 384×288, 640×512 or 1024×768.The array sets how wide a field of view still resolves a target, and it is what the delivered inspection report is judged against.
IFOV and spot sizeInstantaneous field of view in mrad, plus the spot size at the working distance you will actually survey. Require a target to span at least 3×3 pixels.IFOV, not array size, decides whether a loose lug is a resolvable hot spot at three metres or one blended pixel. This is the number that separates two cameras of the same pixel class.
Thermal sensitivity (NETD)≤50 mK at a 30 °C target, and ≤40 mK where the survey covers building envelope or other low-contrast targets. Require the reference temperature and F-number the figure is quoted at.Thermal sensitivity decides whether a 2 °C delta on a matte surface is visible or lost in noise, and a mK figure quoted at an unstated reference is not comparable.
Range and accuracy−20 to +150 °C for electrical and building work, accuracy ±2 °C or ±2% of reading, with the calibration basis and emissivity setting stated.A camera with a 650 °C top end that is less accurate at 30 °C fails an electrical deliverable. Accuracy is only valid inside a stated range.
Radiometric outputRadiometric JPEG or TIFF with embedded calibration, a documented export format, and the analysis software licence included in the price.Non-radiometric files cannot be re-analysed after the site visit, and a locked software licence turns a one-off deliverable into a permanent subscription.
Frame rate and streaming9 Hz or 30 Hz stated explicitly, and RTSP / H.264 output where the feed has to reach a VMS or command post.Export-controlled models are frequently capped at 9 Hz, so a specification that assumes 30 Hz live video can only be met by a restricted camera.
Window or dome opticWindow material and anti-reflective coating named by the manufacturer: germanium with a broadband 8–14 µm AR coating, heated where dew or icing is expected.An uncoated germanium window reflects roughly a third of the incoming LWIR at each surface, and a silicon window blocks the band entirely. Both are paid for at the detector.
Environmental and mountingIP rating, operating temperature range, shock and vibration standard, and the mechanical and electrical interface — mass, mounting pattern, supply voltage, draw.Integration failures on an airframe are almost always mass, power or ingress protection, not optics. Stating them keeps an unsuitable payload out of the bid.

UAV thermal payloads: the integration conditions

An airborne payload is a systems-integration purchase, not a camera purchase. These are the conditions a payload requirement has to state, and the two compliance checks that sit on top of them.

Mass against rated capacity

State payload mass with gimbal and cabling, and the aircraft's rated payload at the altitude and temperature you will fly. A payload that flies at sea level at 20 °C can be outside the envelope at 2,500 m and 40 °C.

Stabilisation, not just axes

Require the gimbal axes and the angular accuracy, plus whether it holds geo-pointing in wind. Three axes with poor accuracy and repeatable pointing are different products.

Interface and control

Supply voltage, current draw, connector, and how the payload is commanded — MAVLink, SBUS, Ethernet. An interface with no published documentation becomes an engineering project on delivery.

Video and telemetry out

Codec, resolution, latency, and the RTSP or UDP stream a ground control station will consume. Ask for the stream specification in writing, not a demonstration.

Environmental rating

IP rating and operating temperature. A payload rated for a lab is not a payload for a fireground or a substation in February, and the rating is the manufacturer's to state.

Airframe compliance

The aircraft carries its own restriction: the FY2024 NDAA's drone provision bars federal agencies from procuring aircraft manufactured in a covered foreign country. A compliant payload on a barred airframe is still a barred system.

Payload compliance

Section 889 status of the payload manufacturer, confirmed in writing. Aerial thermal is where most of this catalog's verified NDAA-flagged inventory sits — 68 of the 113 airborne thermal and survey payload listings carry the flag.

Export control

A payload flagged as export restricted cannot ship internationally, whatever the end user is. One listing in the catalog currently carries that flag, so check it before the solicitation closes rather than after award.

Airborne thermal and survey payloads are the deepest part of the catalog: thermal payloads and airframes and the full aerial catalog. Aircraft restrictions are set out on the drone compliance page.

Optical domes and windows

The aperture in front of the detector is part of the optical system, and the wrong material removes signal the detector can never recover. These are the materials a specification will be asked about, and what each one actually transmits.

IR dome and window materials by transmission band and application
MaterialTransmissionWhere it belongs
Germanium8–14 µm (LWIR)The default dome and window material for LWIR thermography and gimbal payloads. Opaque to the eye, so a germanium aperture is visibly a thermal-only port.Reflects about a third of the incoming LWIR at each uncoated surface. Require a broadband 8–14 µm AR coating, and a hard carbon (DLC) layer where the window is exposed to sand, salt or cleaning.
Chalcogenide glassVisible to LWIRMoulded amorphous glass that transmits across the visible and the LWIR band, which makes it the choice when a colour camera and a thermal core share one aperture and have to stay boresighted.Softer and more expensive than germanium, and the transmission curve varies by composition — ask for the measured curve, not a nominal band.
Silicon1.2–7 µm (SWIR / MWIR)Hard, cheap and common on short-wave and mid-wave systems, including machine-vision and laser applications.Blocks the 8–14 µm band. A silicon window specified in front of a LWIR core leaves the camera blind, and this is the most common window mistake in a written specification.
Zinc selenide0.6–21 µmVery broadband and used in laboratory benches and CO₂ laser optics where transmission across bands matters more than durability.Soft, easily scratched, and toxic to machine — not a field window for a deployed camera.
Sapphire0.25–5.5 µmExtremely hard and abrasion resistant, which is why it appears on mid-wave and multispectral apertures that take impacts.Not a LWIR window. Its hardness does not compensate for a transmission band that stops at about 5.5 µm.

Dome or flat window

A hemispherical dome lets a pan-tilt head look through a full half-space without a moving seal, at the cost of aberrations the camera lens has to be designed to correct. A fixed gimbal usually gets a flat window, fitted slightly tilted so its own reflection never lands back on the detector. Either way the aperture has to be sealed to the housing's IP rating and, in a climate where dew or icing is normal, heated.

Thermisight Dynamics does not stock bare optical components or perform window replacement. The cameras and payloads we supply arrive with the manufacturer's sealed aperture, and for a specification we confirm the window material, coating and heating from the manufacturer's datasheet in writing.

The NDAA position, counted per listing

Compliance is a property of the camera and its manufacturer, never of the store, so it is recorded per listing rather than claimed for the catalog. The counts below are the live figures, and they differ by what is being bought: airborne thermal is where the verified flag sits, while the handheld industrial thermography line is still awaiting manufacturer documentation and is therefore unverified.

98of 302 listings are flagged NDAA Section 889 compliant, from 12 manufacturers, as of November 2026.

A listing carries the NDAA flag when its manufacturer is based in the United States or a treaty ally and is not a covered entity under Section 889 of the FY2019 NDAA, nor owned or controlled by one. For aerial systems this also keeps the aircraft outside the Chinese-manufactured drones federal agencies are barred from buying.

  • Inspired Flight17
  • WISPR17
  • MicaSense10
  • SIG SAUER10
  • Trijicon10
  • ACSL Inc9
  • Freefly8
  • Teledyne FLIR7
  • Sentera5
  • GreenValley International3
  • GeoCue1
  • FoxFury1

An unflagged listing is unverified, not non-compliant: brands whose ownership or manufacturing origin we have not confirmed in writing stay unflagged until the manufacturer documents it, and we do that before an order is placed. The flag is filterable — open the Hunters, Industrial or Drone catalog and switch on NDAA §889 compliant in the quick filters.

How Section 889 attaches to a specific camera, why HIKMICRO and Dahua are covered equipment no reseller can cure, and what belongs in the contract file, is set out in the NDAA §889 guide. Trade Agreements Act status is a separate question, and no listing carries the TAA flag yet while manufacturer origin documentation is collected — treat it as confirmed on the quote.

Volume pricing tiers

The tier is set by the total unit count on one quote and applies to every line on it, so a mixed order of payloads, cameras and spares is priced as one quantity.

Thermisight Dynamics volume discount tiers by total unit count
TierTotal unitsDiscount
Standard1 to 40%
Bronze5 to 195%
Silver20 to 4910%
Gold50 to 19915%
PlatinumApproval required200+20%

How a specification becomes an order

Nothing is charged until a quote is accepted, and compliance documentation is confirmed before the order is released.

  1. 1

    Send the requirement

    Name the models or the specification, the unit count, the ship-to address and any deadline. A single line of text is enough to start.

  2. 2

    We route it to the manufacturer

    Every request is recorded and sent automatically to the authorized contact for that brand, with a copy to our team, so pricing comes from the source instead of an estimate.

  3. 3

    Quote with tier pricing and terms

    The quote carries a quote number, the tier discount applied to each line, and the NET terms offered. Add a PO number or request a line of credit on the same request.

  4. 4

    Direct shipment from the brand

    Thermisight Dynamics holds no inventory. Approved orders are released to the manufacturer for direct shipment, and tracking is recorded against the order.

Specifier questions answered

Thermal imaging camera and drone payload with specification sheet on a black surface

Specify 8–14 µm (long-wave infrared) for building envelope, electrical, mechanical and public-safety work, because that is where targets near ambient temperature radiate most of their energy. Use 3–5 µm (mid-wave) only for hot targets such as kilns, flare stacks or engine exhaust, where the shorter band gives better contrast against a hot background.

Specify 50 mK or better at a 30 °C target for general electrical and mechanical inspection, and 40 mK or better where the survey covers building envelope or other low-contrast targets. Thermal sensitivity is only comparable when the reference temperature and F-number are stated alongside it, so require both in the specification.

Germanium, with a broadband 8–14 µm anti-reflective coating and a hard carbon layer where the aperture is exposed. Silicon transmits only to about 7 µm and blocks the LWIR band entirely, so a silicon window in front of a long-wave core leaves the camera blind. Chalcogenide glass is the option when a visible camera and a thermal core share one aperture and must stay boresighted.

Per listing, not as a whole. 98 of the 302 live listings carry the NDAA Section 889 flag, and 68 of those are airborne — 53 thermal payloads and airframes plus all 15 survey payloads. None of the 13 handheld industrial thermography cameras currently carries the flag: they are one brand whose ownership and manufacturing origin is still being documented, which makes them unverified rather than non-compliant, and we confirm the status in writing before an order is placed.

Yes. Airborne thermal payloads and airframes are quoted like any other procurement line, with volume tiers, NET 30 or NET 60 terms and a quote number to reference on the PO. Both halves of the system are checked separately: the airframe against the FY2024 NDAA drone restriction, and the payload against Section 889.

No. Thermisight Dynamics supplies complete cameras and payloads with the manufacturer's sealed aperture, and does not stock bare optical components or perform window replacement. For a specification we confirm the window material, coating and heating from the manufacturer's datasheet in writing.

Send a specification or a requirement

Send the specification, the model, the quantity and the ship-to address — or the requirement itself, if the specification is not written yet. The B2B portal and the procurement quote form both reach the same team, and catalog stock sits in the industrial thermography and drone storefronts.

Or call (503) 568-8124 during Mon–Fri 9–5 PT, or see the support center.

Cite this page

Thermisight Dynamics LLC, “IR Thermography & UAV Payload Procurement for Specifiers”, https://thermisightdynamics.com/thermography. Last updated November 15, 2026.

Catalog counts, flags and pricing tiers are stated as of the update date above and are confirmed on the quote itself.